Skip to main content

Banner Sponsors

Past Time Bears - Artist bears designed and handcrafted by Sue Ann Holcomb
Shelli Makes - Teddy bears & other cheerful things by Shelli Quinn

CrawlyCreepies Posts: 89

I feel like I can never get my stitches to line up on both pieces when I sew on my machine.
10481703_10201798733044795_2645343610900506004_n.jpg
My pins were about 3/4" apart. Any tips on how to keep this from happening?

dangerbears Dangerbears
Wisconsin
Posts: 6,021
Website

Could you describe the problem a bit more? (In the photo, I see what looks like a tangle of thread and stitches. Is that it?)

Becky

CrawlyCreepies Posts: 89

Oh yes, that tangle is where the stitches went, the tangle is an unrelated problem I get when I reverse the direction of my stitching.

edmondnutmeg Padfield bears
Derbyshire
Posts: 1,343
Website

Hummm are you sewing felt? or some fabric with a slight stretch in it? Either way it may have something to do with your feed dogs (that is the 'teethy bits that are on the bottom plate of your machine that moves the fabric along as you sew) These types of fabric can some times grip the fuzzy surface of the material and not flow as smoothly it happens a lot when you turn the direction of sewing ie when going in reverse and turning round shapes. Try altering the pressure of the foot to see if that helps or sewing with a layer of tissue paper underneath (between the bottom plate of the machine and the underneath of piece you are sewing) that you just tear away after you have finished sewing. I am no expert but hope this might help
michelle

dangerbears Dangerbears
Wisconsin
Posts: 6,021
Website

Those are good ideas, Michelle. It does look like fleece or some kind of fuzzy and/or stretchy fabric.

There are numerous variables to play with, including the pressure on the foot. The tangle is a clue that you might be using the wrong thread, or the tension (top and/or bottom) may need to be adjusted.

I also notice that the part that slipped isn't pinned (in the first pic? the back of a leg?) I'd use smaller pins, a smaller seam allowance, and make sure that the part you're working on is secured. If the fabric is slipping, you could even place some pins in the middle of the piece to prevent some of the movement.

Let us know how it goes!

Becky

CrawlyCreepies Posts: 89

Thanks everyone!

It's cruddy craft felt, I don't have any muslin to do pattern tests on right now. The final piece will be velvet. I'll definitely try the tissue paper thing next time I sew on fleece though.

I didn't know I could change the presser foot pressure! I'll look up how to do that in the manual.

I never get the tangles as I sew in a straight line, it's only when I back up over my stitches at the beginning/end of a seam. I assumed it was caused when the tails of the thread got caught up in the seam.

What's top/bottom tension? I assume I can figure out how to fix that in the manual?

I take the pins out as I'm sewing because I thought you could break a needle if you left them in. Am I wrong about that? Should I leave them in? I've got smaller pins I can switch to, but I feel like they aren't as sharp so I don't use em much. Putting pins in the middle is a good idea.

dangerbears Dangerbears
Wisconsin
Posts: 6,021
Website

On a machine, you're sewing with two lengths of thread, and you can change the tension of the thread coming from the spool on top as well as the thread coming from the bobbin. Your manual or a search online can help you with the tension adjustment. (I think the tangle is probably due to tension or thread type.) And I agree -- you'll usually remove each pin right before the needle gets to it, but with care, there may also be times you want to leave in place. Just do that very slowly if at all. bear_original

Becky

jenny Three O'clock Bears
warwickshire uk
Posts: 4,413
Website

I always have the pin points sticking out like a hedgehog and then it's perfectly ok to machine over the points as that end is much thinner.
I tack mine now though..I find it's much better as it holds the edges together...and what I lose in time by tacking I gain by getting the stitching right first time on the machine. Occasionally on very big bears I just pin and machine but mainly I tack now.
You do only need half that seam allowance though and go slow. I remember someone once told me "no matter how slowly you machine it will always be faster than you hand sew , so take your time,"

CrawlyCreepies Posts: 89

Thanks for the help, I had no idea seam allowance size could impact this! I'm glad to know its ok to sew over pins. I hit up the fabric store today and got some smaller pins that are sharper than my old, dull ones. I also got some muslin, that'll be much easier to make pattern tests with.

Figartteddy Posts: 14

Try tacking the edges together first before machine sewing. I found that even with pinning edges very closely together, sometimes only a quarter inch between pins that somehow one edge slipped out of place as I sewed over the pins carefully.

CrawlyCreepies Posts: 89

That's a good idea, Figartteddy. The plushie I'm working on right now is too small for the machine, but I'll definitely have to try that for the next larger one.

Board footer

Powered by FluxBB

Banner Sponsors


No Monkey Biz - Domain name registration, hosting
Intercal Trading Group - Your mohair supplier