Banner Sponsors
For artists and collectors sponsored by Intercal...your mohair supplier and Johnna's Mohair Store
SUE GORRIE FOLKARTDoes anyone have some tips for working with velvet? I am trying to make a cotton lined velvet coat for my bear and am finding it a challenge not only because of the stretch of the fabric, but the pile affects the sewing. Trying to do most of it by hand, but it's still hard to get it just right. It looks okay, but not as nice as I had planned. Seems I end up with more or less fabric in one area making it uneven in the end, running out of lining or velvet. It's as if the pattern pieces were different sizes. Perhaps my stitches are too tight? It ends up looking like the lining is gathered in some places.
Anywho, it's VERY frustrating! 
Any suggestions to making working with velvet easier????
Thanks
Sue
JeannieB BearsHi Sue,
Don't know if this helps....maybe someone more experienced will post....But, I have used velvet to make a bear and had similar problems. I hand sew .....I used very small stitches and for every five stitches I used a locking stitch. This helped keep the "gathering" from happening to me. I'm sure there is better advice out there.....and your little jacket looks great to me! 
Hugs,
JeannieB 
Hmmm.... Hoping you would have had some answers to your question as enquiring minds want to know. I often have the same problem and had my velvet edges just fall apart as it sheds so easy. On another note, I really like the shade of blue you've chosen and think the jacket looks darling.
I treat velvet the same way I do pile fabrics and mohair - I fray-check every edge of the pattern piece, shave the seam allowence. and I don't use pins or alligator clip, which can crush and mark the pile, but 1/2" binder clips from Staples, which hold tight. flip off easily and don't leave marks if you clip to the seam allowence.
fray-checking will help stop the shifting and streching of the fabric and stablize it, much the same as it does when you coat the inside of knit=back furs
for more tips on working with velvet:
Angela's Bear GardenGreat advice! I was going to suggest to always baste your pieces carefully before sewing to prevent the garment fom slipping or puckering. The link kellydean left has excellent tips!
Shane and Steven of the Bear Guys could most likely help you with this as part of their penquin costumes was velvet- try tp pm them
Hugs
Gail
Love Bear ForeverYour coat is beautiful. I have some experience in velvet and hope those will help.
1st While cutting the velvet, make sure you will have your cut piece in all same direction (one way cutting).
( Because if you cut in 2 ways, it will have different shade happen in your coat.)
2nd while sewing the velvet with and un-stretch lining, I suggest -
1. Sew from inside out. leave a hole at the bottom then turn it front so it is more easy for you to control the sewing.
2. Pin the cut piece before your start sewing. So while you hand sewn or machines sewn you will not pull the velvet fabric and make them un-even.
Pin will not destroy the fabric so do not worry about it.
3. Soft fusing interlining add in placket and collar. With the fusing interlining the velvet fabric will not be stretch.
Hope this will help.
Matilda Huggington-beareI also fray check but very carefully and try for just the edges. I dont pin but I put in little basting stitches and knot them in all the key points. I do this with all my pattern pieces regardless of what fabric or what I am making.
And I do it this way when I make them little coats. Works for me. The stitches can be removed after its sewn.
You could try putting a strip of tissue paper between the fabrics as you sew, this may help, and make sure you match up, this will help to know where to ease in the fabric, if neccessary. If you can neaten the edges before you start sewing, this will prevent fraying. Either hand oversew or zig zag on a machine.
I love velvet it does look great, but it is a nightmare.
I made an outfit from velvet once, in my art college days and I actually glued the hem with a fabric glue, it worked a treat. So if you get really desperate you could just glue it together ?
Sunshine Coast, QLDCan you not iron a non-stretch backing onto the back of the velvet? Like the stuff from Sassys...dont remember what its called!
SUE GORRIE FOLKARTHere's my new bear wearing his little velvet coat. Thinking of putting him up for auction, but I really want to keep this one! 
Hope he goes to someone who will give him some love and kisses and not just keep him in a glass case.
Thanks to everyone for the tips! I did try out thicker thread. That helped a bit. I think I will glue the seams next time as I did have them tacked every inch and it was still a problem. To iron the collar flat, I used another piece of scrap velvet on top with a cotton dish towel over that on low heat, so as not to crush the pile. Velvet definitely requires alot of patience! 
Matilda Huggington-beareWOW doesnt he look handsome 
I can understand why you would want to keep him. He looks like he would be just the right type of bear to tell all your secrets to. A trusted discreet bear.
That jacket looks like it was worth all the pain Theyre wonderful together Sue.
